Wires in Mast

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   How do you all run your electrical (instrument & light) wires from inside the mast to the interior of the boat?

Mine run out the front of the mast, near the deck, and then go through the deck adjacent to the mast.  I do not like this arrangement for a variety of reasons. I am thinking of drilling a hole through the bottom of the mast base, another hole through the mast step on the deck, and then another hole through the compression post under the mast.  All so I can run the cables through the bottom of the mast to the inside of the boat.  I realize that some water will get in the boat with this arrangement, but I think it would be minor and overall this would be a better arrangement.

Thoughts?

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
khardy Members Profile Send Private Message Find Members Posts Add to Buddy List Commodore Joined: 22 June 2004 Location: United States Status: Offline Points: 132	Post Options Post Reply Quote khardy Report Post Thanks(0) Quote Reply Topic: Wires in Mast Posted: 24 March 2015 at 2:46pm
	How do you all run your electrical (instrument & light) wires from inside the mast to the interior of the boat? Mine run out the front of the mast, near the deck, and then go through the deck adjacent to the mast. I do not like this arrangement for a variety of reasons. I am thinking of drilling a hole through the bottom of the mast base, another hole through the mast step on the deck, and then another hole through the compression post under the mast. All so I can run the cables through the bottom of the mast to the inside of the boat. I realize that some water will get in the boat with this arrangement, but I think it would be minor and overall this would be a better arrangement. Thoughts?

fatjohnz Members Profile Send Private Message Find Members Posts Add to Buddy List Commodore Joined: 05 August 2006 Location: United States Status: Offline Points: 304	Post Options Post Reply Quote fatjohnz Report Post Thanks(0) Quote Reply Posted: 24 March 2015 at 3:36pm
	My boat is set up as you describe, with the wire running thru the bottom of the mast, into the mast base, and into the compression post. They exit the bottom of the post into the bottom of the front starboard bench. Now that I think of it, my racing compass wire is running external to the mast thru a hole behind the mast base. I should rerun this thru the mast... js

Bill Layton Members Profile Send Private Message Find Members Posts Add to Buddy List Commodore Joined: 15 September 2002 Location: Canada Status: Offline Points: 551	Post Options Post Reply Quote Bill Layton Report Post Thanks(0) Quote Reply Posted: 24 March 2015 at 5:28pm
	Passing wires thru the mast base casting has caused water infiltration at the base of the compression post and in many boats rotted out the large wood compression block under the ring frame. Now that we know this we should avoid passing wires into the compression post. The solution is to pass them thru the deck near the mast casting and use this fitting which works very well http://www.westmarine.com/buy/blue-sea-systems--cableclam-waterproof-through-deck-fittings--P003_094_003_008 http://www.google.com/imgres?imgurl=https://c2.staticflickr.com/8/7142/6609947745_9b05463c3f.jpg&imgrefurl=https://www.flickr.com/photos/26510883@N07/6609947745/&h=375&w=500&tbnid=EDiPiMKUKrp2nM:&zoom=1&docid=Kop68RSJWM4dPM&itg=1&ei=3dYRVdvuD63HsQSto4GQAQ&tbm=isch&ved=0CCMQMygGMAY

Ron Waterson Members Profile Send Private Message Find Members Posts Add to Buddy List Commodore Joined: 21 October 2014 Location: Rivals, KY Status: Offline Points: 118	Post Options Post Reply Quote Ron Waterson Report Post Thanks(0) Quote Reply Posted: 25 March 2015 at 11:18am
	Unfortunately, I have both situations. Agreed that the exposed wires on the deck cause a problem with bowman's feet occasionally, but the water infiltration from exposing the post is not an acceptable alternative in my opinion. One of the previous owners ran the wires down the compression post...the water comes out the bottom of the post and rots the bulkhead, and apparently (see previous post) can do further damage. I'm replacing my starboard bulkhead right now. We'll be dropping the mast and correcting the leak at the mast base also. I suppose one could glass the bulkhead base where it meets the post and ring frame...perhaps forcing the water to run to the bilge. One comment pertaining to the time I spent reconnecting instrument wires followed by a couple reminders to watch his step, and I didn't have any problems for the second half of the racing season. (:
	Hull 147 - Angel's Share

dmarkc Members Profile Send Private Message Find Members Posts Add to Buddy List Rookie Joined: 29 December 2006 Location: United Kingdom Status: Offline Points: 13	Post Options Post Reply Quote dmarkc Report Post Thanks(0) Quote Reply Posted: 25 March 2015 at 11:35am
	I agree too. I take my wires out of the mast, through the deck gland and then internally run through the compression post to tidy everything up. My solution to foredeck's feet...! https://www.dropbox.com/s/94ixmvc54cgpsq1/IMG_0132.jpg?dl=0

Ron Waterson Members Profile Send Private Message Find Members Posts Add to Buddy List Commodore Joined: 21 October 2014 Location: Rivals, KY Status: Offline Points: 118	Post Options Post Reply Quote Ron Waterson Report Post Thanks(0) Quote Reply Posted: 25 March 2015 at 3:50pm
	LOL...That'll teach to never go barefoot on the foredeck too.
	Hull 147 - Angel's Share

khardy Members Profile Send Private Message Find Members Posts Add to Buddy List Commodore Joined: 22 June 2004 Location: United States Status: Offline Points: 132	Post Options Post Reply Quote khardy Report Post Thanks(0) Quote Reply Posted: 27 March 2015 at 8:28am
	thanks all for your comments. I'll keep running them through the deck. ken